Corona Pool Builders provides professional pool heaters & heat pumps in Corona, CA for residential and commercial properties across the Inland Empire. Pool heater installation extends a Corona swim season that is already generous into something close to year-round, and it is one of the most common upgrades we add during a remodel because the plumbing is already open. Unheated, an Inland Empire pool is comfortable from roughly late May through September. Add a heat pump and a cover and most of our clients swim from April into November, and the spa runs all twelve months. Three technologies, three jobs. An electric heat pump moves heat out of the ambient air rather than burning fuel to create it, which makes it dramatically cheaper per degree and well suited to our mild shoulder seasons — it is the right answer for holding a pool at temperature through spring and autumn. A gas heater delivers high output and fast recovery, which makes it the right answer for a spa and for anyone who wants the pool hot for a specific weekend rather than warm all week. Solar collectors are genuinely effective on a south or west-facing Corona roof given the number of clear hot days here, cost essentially nothing to run, and pair naturally with a cover. A common and sensible package is a heat pump or solar on the pool and gas on the spa. Sizing is calculated rather than guessed, from surface area, target temperature rise, wind exposure — which on the hillside lots and through Temescal Canyon is a real factor — and whether a cover is used. An undersized heater runs constantly and never arrives; an oversized gas unit short-cycles and destroys its own heat exchanger. Installation covers correct gas line sizing and pressure, venting clearances, bonded and GFCI-protected electrical for heat pumps, and integration into the automation system so the spa can be brought up from your phone on the drive home. We repair as well: ignition and flame sensor faults, pressure switch failures, heat exchangers scaled shut by hard water, and the very common no-fire call that turns out to be a dirty filter starving the heater of flow. And the cheapest heat you will ever buy is a cover.
With 15+ years of experience, our licensed and insured team brings the right materials and equipment to every job — PebbleTec and pebble aggregate interiors, polished quartz resurfacing, full chip-out and bond beam repair, glass mosaic waterline tile, travertine and porcelain coping, Title 24 variable-speed pumps — and backs the work with a written workmanship warranty. We serve Corona and nearby communities including Riverside, Moreno Valley, Ontario, Rancho Cucamonga.
What We Handle
Everything our pool heaters & heat pumps in Corona covers
One crew, one point of contact, and the full range of pool heaters & heat pumps work in Corona, CA. If it is on this list we do it in house rather than handing it to a subcontractor:
- pool heater installation
- natural gas pool heater
- electric heat pump pool heater
- spa heater replacement
- pool heater repair
- heater sizing and BTU calculation
- solar pool heating
- pool heater not firing
- heat pump vs gas heater
- season extension heating
- commercial pool heating
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Corona services.
Materials, equipment and how we do pool heaters & heat pumps
The difference between pool heaters & heat pumps that lasts and pool heaters & heat pumps that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with PebbleTec and pebble aggregate interiors, polished quartz resurfacing, full chip-out and bond beam repair, glass mosaic waterline tile, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Corona job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of pool work in the Inland Empire means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do pool heaters & heat pumps outside Corona
Corona Pool Builders covers Corona and the surrounding communities of the Inland Empire. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Pool Heaters & Heat Pumps in Riverside, CA — Riverside County, population 315,000
- Pool Heaters & Heat Pumps in Moreno Valley, CA — Riverside County, population 208,600
- Pool Heaters & Heat Pumps in Ontario, CA — San Bernardino County, population 175,300
- Pool Heaters & Heat Pumps in Rancho Cucamonga, CA — San Bernardino County, population 174,500
- Pool Heaters & Heat Pumps in Murrieta, CA — Riverside County, population 110,900
- Pool Heaters & Heat Pumps in Temecula, CA — Riverside County, population 110,000
Start on the Corona Pool Builders homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Corona Chooses Corona Pool Builders
- ✓Remodeling and resurfacing specialists — it is most of what we do, not a sideline
- ✓Over 15 years across Corona, Norco, Eastvale and the Temescal Valley
- ✓Honest shell inspection before you spend a dollar on finishes
- ✓Full chip-out prep, not a bond coat over a failing surface
Every pool heaters & heat pumps project in Corona gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free pool heaters & heat pumps free estimate in Corona, or request a quote and we'll get right back to you.